A. Main parameters: 1.Host size: 7. 9m x 2.5meters, open double door, width 4.8 m.
2.Two wire disk size: 1.75m x 1.75m
3.Two wire disk side by side, with host distance about 0.85m. The spacing is about 1. 5m.
4. Minimum occupation area: 10. 5m x 5m
5. Total installed capacity 27kW. Maximum simultaneous use capacity 20kW.
B. Installation:
"host", "wire", "oil station" on the flat ground. The main engine is adjusted to the basic level, the bottom is set at six points, and the door is opened or closed symmetrically. At this point, if the door closes a certain angle, the door will automatically continue to close. Conversely, if the door opens a certain angle, then the door will automatically continue to open. This shows that the host level is good, otherwise it should be re adjusted. The body and the supporting force to prevent bending welding. The bottom of the dial is also adjusted to the basic level. Its two bent support frames are located in the rear.
2.The machine has phase relay, if the power supply phase sequence is wrong, the machine will not work.
Before sending the power, you should do the following work: press the "emergency stop" button on Gate No.1 and No.2 to ensure that there is no debris on the parts.
Especially the following three parts: (1) the opening of the knotting device has no sundries on the sprocket. There is no debris on the two rail beside the pulley. Shearing the mouth and its related parts without debris. The steering of the motors shall be in accordance with each other. The factory has been adjusted (except the oil pump) before the production, and the internal wiring and motor steering shall not be changed.
C. Usage
1.The "wire disk" will be about 6 Phi when it opens. 5mm's two bales of Baling thread are individually lined with two "reels."". Close the support frame to make sure it doesn't turn.
2. the packing line is drawn through the center hole of the support frame and passes through the curved pipe
The button is removed by the guide wheel to complete the packing preparation.
3. place the packaged wire on the two roller of the main engine. Press the "press" button, let the pulley close to the wire rod and compress the right amount, press the "roll" or "anti roll" button to round the wire round, continue to press the "pressing" button until the fully compacted wire automatic stop. Press
The "spinning" button is artificially assisted to spit out an appropriate packing line and is manually clamped through the center of the wire rod through an open chain wheel to clamp the thread through an open chain wheel. Attention: the thread should be below the "packing line" line.
4.Press the "tight" button at tighten the packing line properly, and let the packing line bounce naturally Confirm that the two packing lines are located at the back of the opening sprocket, and press the "knot" button, the machine will automatically tie and cut off, and then complete the bundle in one direction. "Single cut" means only cut off, but not knotted. Note: excessive tightening or no natural rebound is likely to break the packing line.
5. let wire to 90 degrees, repeat the completion of the other direction of the bundle.
6. press the "back" button, turn off the pulley, lift the wire, the whole process is completed.
D. Hydraulic station adjustment
1. hydraulic station adjustment see (hydraulic principle diagram, electrical principle diagram 5, 6, 7, 8 pages). Adjustment principles: use as little compaction as possible. That is, enough is enough. Excessive compaction can cause serious damage to the frame, turntable, roller and other components!! If it is found that the pressure is too large, although it can work properly, it should be adjusted in a timely manner. It's very beneficial for the protection of the equipment.
2. if it is found that the spinning and tension are weak, or the packing line is compressed, the pressing force of the four pressing devices around the guide wheel is not suitable. Just adjust it properly.
3. if it is found according to the "knot button" after the opening, the opening is not accurate alignment of the sprocket is ahead, according to the following steps: according to the regulation of "knot" button for more than two times (action after the interval greater than 2 seconds) exact induction fork stop position. Move carefully
The corresponding button on the side of Gate No. 1 in the distribution cabinet accurately opens the openings of the opening sprocket to the correct position in front of the straight wheel. At this time, the inductive shift fork has deviated from the stop position just recorded. Release the screws and adjust the fork to the "exact position", i.e., complete the adjustment. Press the "knot" button to check whether the opening of the open sprocket is accurately aligned. If not, fine tune the induction fork until accurate alignment is ahead (if the opening of the sprocket is biased, the induction fork is shifted downwards; if it is lower, it is raised).
E. Maintenance 1. when the equipment does not work, the pulley should be stopped at the end to prevent the piston rod from being damaged.
2., active friction parts should always add lubricant. In particular, the following 2 parts: open copper openings on both sides of the open sprocket, and butter from the small holes. Chains everywhere.
Note 3. oil station
F. notes
1. The boldface part of the above.
2. for a variety of packaging line card in the opening lead sprocket, should be careful removal. It is possible to move the openings of the opening sprocket accurately to the correct position in front of the switch with the right button on the side of Door No. 1 in the distribution cabinet. According to the "knot" button to start the opening chain only clamped more tightly, until the destruction of the opening and the opening cover copper chain.
3. when a bundle of packing line is about to run out and not enough for the next use, the end of the residual line should be spit out from the front. Instead of trying to push the last line out of the front line. This will cause the two wires to be stuck together in the device, harder to remove, and prone to damage to the equipment.
G. wearing parts
Open copper cover. Open sprocket. Shear guide body and shear nozzle.See the shear cylinder seal.
Before sale: design the suitable machine based on the specific demands
Medium sale:
1.Based on customer's demand to offer moderate quotation project 2.Accept customers to visit our factory
3.Help customer work out the schedule in china
After-sale:
1.On-site training personnel 2.Appoint special aftersale service staff, arrived at the scene guide clients installation and commission
Xi'an Weikeduo Electrical & Mechanical Equiment Co., Ltd.
With more than 20 years experience in metallurgical industry, The main business scope for the metallurgical machinery, high-speed gear box, hardened gear reducer. High-speed wire rod, bar, special steel rolling mill production line design, production, sales and installation; As well as for the aviation, steel, oil, electricity, coal mining machinery to provide intelligent re-manufacturing laser quenching, welding, cladding supporting processing, surface corrosion and wear-resistant alloy protective processor full set of technology development, services and applications. Crack detection of the equipment and spare parts, CMM measure and Gear detection. Products through the ISO9001 certification, the use of "Hangji" registered trademark of Shaanxi famous brand, with more than 10 patented technology, the establishment of a complete research and development, production and quality assurance system for high-tech enterprises.
){kind=link}